2021 Superior 6203T44PWP Screening Plant

SUPERIOR PORTABLE GUARDIAN® 6203 TWIN 44" AGGREDRY® WASH PLANT EQUIPPED AS PER BELOW:

PLANT SPECIFICATION:
-   CONSTRUCTION: MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL BEAMS
-   DISCHARGE CHUTE: MANUAL ROLLAWAY CHUTE CONSTRUCTED OF 1/4" STRUCTURAL STEEL WITH 1/4" WELD-IN AR 400 LINER
-   BLENDING CAPABILITIES: 1/4 PANEL BLENDING GATES IN DISCHARGE CHUTE SYSTEM
-   TOP DECK DISCHARGE: OVER THE KINGPIN OR BLENDS DOWN TO BOTTOM DECK CROSS CONVEYOR
-   MIDDLE DECK DISCHARGE: TO MIDDLE DECK CROSS CONVEYOR OR BLEND DOWN TO BOTTOM DECK CROSS CONVEYOR
-   BOTTOM DECK DISCHARGE: TO BOTTOM DECK CROSS CONVEYOR OR BLEND UP TO TOP DECK DISCHARGE
-   WALKWAY: AROUND BOTH SIDES AND FEED END OF SCREEN; ENDS WHERE SCREEN MEETS DISCHARGE CHUTE, MANUALLY FOLDS ONE SIDE (NON-DRIVE SIDE)
-   OBSERVATION PLATFORM: FOR THE DEWATERING SCREEN
-   WALKWAY ACCESS: TO BOTH SIDES OF CHASSIS WITH (2) VERTICAL SLIDING LADDERS
-   ACCESS GATES: SELF CLOSING HINGED GATES AT ALL WALKWAY ACCESS POINTS
-   SLURRY HOPPER: FOLDS MANUALLY FOR TRANSPORT WITH (2) 2.5” WATER LINES
-   GREASE PACKAGE: REMOTE GREASE STATION, MULTIPLE GREASE POINTS OUTSIDE OF CHASSIS FRAME
-   SAFETY TIEOFF: OVERHEAD SAFETY TIE OFF POSTS WITH CABLE BETWEEN TWO POSTS
-   GUARDING: FOR ALL DRIVE AND TAIL PULLEYS

CHASSIS SPECIFICATIONS:

-   AXLE: QUAD AXLE WITH (16) 11RX22.5 RADIAL TIRES
-   SUSPENSION: SPRING SUSPENSION
-   BRAKES: COMPLETE AIR BRAKE PACKAGE
-   FIFTH WHEEL: INCLUDED
-   LIGHTS: BRAKE AND DIRECTIONAL SIGNALS
-   MUD FLAPS: INSTALLED BEHIND TRANSPORT WHEELS
-   CRIBBING LEGS: (8) FIXED STRUCTURAL STEEL CRIBBING LEGS
-   LANDING GEAR: 2-SPEED CRANK DOWN TO AIDE IN LIFTING OFF AND ATTACHING TO TRUCK

SPRAY SYSTEM AND UNDERFLUME

-   UNDERFLUME CONSTRUCTION: ¼” AR PLATE
-   UNDERFLUME SPRAY BARS: LOCATED AT FEED AND DISCHARGE POINTS
-   MANIFOLD: 8” BOLT FLANGE FOR FRESH WATER HOOKUP
-   MANIFOLD DISTRIBUTION: DISTRIBUTES WATER TO SCREEN SPRAY BARS, SLURRY HOPPER, FMW WASH BACK & FINES HOPPER

CROSS CONVEYOR SPECIFICATIONS

-   CROSS CONVEYORS: (2) 30” X 12’ LONG SLIDE-IN REVERSING CROSS CONVEYORS
-   DRIVE: CLASS II HEAD END
-   GEAR REDUCER: DODGE SHAFT MOUNT
-   MOTOR: 7.5 HP MOTOR(S) TEFC
-   DRIVE PULLEY: 10” DIAMETER, DIAMOND LAGGED MD CROWN FACED DRUM
-   TAIL PULLEY: 10” DIAMETER MD WING PULLEY
-   BEARINGS: DODGE
-   IDLERS: CEMA C, 5” DIA. ROLLS, SEALED FOR LIFE BALL BEARINGS, 20°
-   BELTING: 3 PLY 3/16 X 1/16 330 PIW
-   BELT SPLICE: FACTORY INSTALLED FLEXCO MECHANICAL FASTENER(S)
-   BELT SCRAPER: (1) EXTERRA PRIMARY SCRAPER PER CROSS CONVEYOR

SCREEN SPECIFICATIONS

-   SCREEN SIZE: GUARDIAN 6X20 3-DECK HORIZONTAL SCREEN
-   SCREEN DRIVE: RIGHT HAND
-   CONFIGURATION: OPERATE IN TRUE HORIZONTAL POSITION
-   SCREEN MOTOR: 40 HP, TEFC, NEMA PREMIUM “DESIGN C”
-   FOLDING MOTOR: MANUALLY FOLDING MOTOR FOR PLANT TO TRAVEL AT 12’6” WIDE
-   SHAFT HOUSING: MILD STEEL PROTECTION CLAMPED TO SHAFT HOUSING
-   SPRINGS: STANDARD COIL SPRINGS
-   FEEDBOX: 24” FEEDBOX WITH ¼” AR LINERS
-   SIDELINERS: STANDARD SCREEN SIDE-LINERS
-   SCREEN MEDIA: CUSTOMER SUPPLIED AND INSTALLED

TOP DECK

-   TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 4’ SINGLE CROWN WIRE CLOTH MEDIA SECTIONS
-   TOP TAKE UP: STANDARD TAKE UP RAILS

MIDDLE DECK

-   TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 4’ SINGLE CROWN WIRE CLOTH MEDIA SECTIONS
-   MIDDLE TAKE UP: STANDARD TAKE UP RAILS

BOTTOM DECK

-   TYPE: HEAVY X-BRACE SINGLE CROWN DECK TO ACCOMMODATE 4’ SINGLE CROWN WIRE CLOTH MEDIA SECTIONS
-   BOTTOM TAKE UP: STANDARD TAKE UP RAILS

MATERIAL WASH SPECIFICATIONS

-   MATERIAL WASHERS: SUPERIOR TWIN 44” AGGREDRY® DEWATERING WASHERS
-   SCREW SPEED: 17 RPM
-   CAPACITY: UP TO 300 STPH (SUBJECT TO CHANGE BASED ON FINAL GRADATION)
-   WEAR SHOES: RUBBER
-   SCREW MOTOR: (2) 20 HP TEFC
-   GEAR BOX: DODGE SHAFT MOUNT
-   DEWATERING SCREEN: INTEGRATED 6X12 DEWATERING SCREEN
-   DEWATERING SCREEN MOTOR: (2) 11.4 HP ELECTRIC VIBRATORS
-   BOOSTER PUMP: (2) 15HP BOOSTER PUMP INCLUDING 2” BALL VALVE TO INCREASE & CONTROL FINES JET DISCHARGE PRESSURE

ELECTRICAL SPECIFICATIONS

-   VOLTAGE: 460 V / 3 PH / 60 HZ
-   PANEL ENCLOSURE: SKID MOUNTED PANEL, WITH LIFTING EYES. TRAVELS ON PLANT AND REMOVED FOR OPERATION
-   COMPONENTS: NEMA WITH START/STOP PUSHBUTTONS, AMP METER, HOUR METER & WARNING LIGHT
-   STARTERS: FOR ALL ON PLANT MOTORS, (2) ADDITIONAL #2 STARTERS (UP TO 25HP MOTORS), & VFD CONTROL FOR FMW MOTORS
-   WIRING: FACTORY SUPPLIED AND INSTALLED WIRING FROM PANEL TO ALL ON BOARD MOTORS